STEEL HEAD LATE MODEL

RULE BOOK DISCLAIMER

The rules and/or regulations set forth herein are designed to provide for the orderly conduct of racing events and to establish minimum acceptable requirements for such events. These rules shall govern the condition of all events, and by participating in these events, all participants are deemed to have complied with these rules. NO EXPRESSED OR IMPLIED WARRANTY OF SAFETY SHALL RESULT FROM PUBLICATIONS OF OR COMPLIANCE WITH THESE RULES AND/OR REGULATIONS. They are intended as a guide for the conduct of the sport and are in no way a guarantee against injury or death to a participant, spectator or official.

The race director shall be empowered to permit reasonable and appropriate deviation from any of the specifications herein or impose any further restrictions that in his/her opinion does not alter the minimum acceptable requirements. NO EXPRESSED OR IMPLIED WARRANTY OF SAFETY SHALL RESULT FROM SUCH ALTERATION OF SPECIFICATIONS.  Any interpretation or deviation of these rules is left to the discretion of the officials. Their decision is final.

The Management of MOUNTAIN VIEW RACEWAY

 

BODIES:

  1. Lucas Oil, SAS body rules apply

  2. Rear deck height max. 38 inches. Will be measured from the rear T-Bar to ground

  3. 8 inch spoiler and sides max, 8 inch of flat surface for spoiler.

  4. Minimum wheel base 103 inches

TIRES:

  1. Fronts open

  2. Rears – Hoosiers 1600/Equivalent or AR56/Equivalent. Must be shoulder plated.

  3. Must punch 50 at any time

  4. No chemical treatment of any kind allowed

  5. 14 inch aluminum wheels only

*Tire samples will be taken

SUSPENSION:

  1. Lucas Oil, SAS suspension rules apply

  2. Carbon fiber drive shafts allowed

  3. Any transmission

  4. Any rear end

  5. Engine set back 6 inches +/- 1 inch

  6. Any ignition

FUEL:

  1. E-85 or gas only. NO alcohol, nitrous oxide, or any other fuels allowed.

*Fuel samples will be taken.

ENGINE AND WEIGHT:

ENGINE A: 2250 lbs min. After qualifying and feature.

  1. Max. 365 cubic inch

  2. Max. Stroke 3.500

  3. Any steel crank and rods

  4. All steel block

  5. Flat top pistons only

  6. Flat tappet cam and lifters

  7. Any steel 23 degree style head with 2 degree tolerance, spec heads are allowed, add 25 lbs. in front of the mid plate

  8. No raised runner heads allowed

ENGINE B: 2300 lb min. After qualifying and feature

  1. Max. 365 cubic inch

  2. Max. Stroke 3.500

  3. Any steel crank and rods

  4. Any steel block

  5. Flat top pistons only

  6. Roller cam allowed

  7. Any steel 23 degree style head with 2 degree tolerance, Spec heads are allowed, add 25 lbs in front of the mid plate

  8. No raised runner heads allowed

ENGINE C: 2400 lbs min. After qualifying and feature

  1. Max. 365 cubic inch

  2. Max. Stroke 3.500

  3. Any steel crank and rods

  4. All steel block

  5. Dome pistons allowed

  6. Roller cam allowed

  7. Any steel 23 degree style head with 2 degree tolerance, spec heads are allow, add 25 lbs in front of the mid plate

  8. Raised runner heads allowed

Engine D: 2500 lbs after qualifying and feature

  1. Max. over 365 to 406 cubic inch

  2. Steel block 

  3. Steel 23 degree style heads (plus or minus 2 degree), spec heads are allow, add 25 lbs in front of the mid plate

  4. Raised runner heads allowed.

No burn off rule, weight is as follows, no tolerance

ALL PROTEST RULES APPLY, VIEW IN GENERAL RULES

© 2019 by Mountain View Raceway.

Proudly created with Wix.com

Like us!
  • Facebook Social Icon

Text :

423-507-2619 

Spring City , TN